NeoECU-Hardware/Architecture/IO_ARCHITECTURE.md

NeoECU V1 Initial Functional I/O Architecture

Purpose

This document records the initial functional I/O architecture for NeoECU V1. It builds on the power architecture and defines the required interface classes, analogue-channel allocation, and intended signal conditioning. It is not a schematic or component-selection document; exact parts, resistor values, pin assignments, connector allocation, and final I/O quantities remain to be confirmed.

The initial ECU controls a single-cylinder four-stroke engine with one injector, one dual-ended dumb ignition coil, crank and cam Hall sensors, temperature and pressure sensors, and an external starter switch.

I/O Summary

Interface	V1 allocation	Functional intent
Crank trigger input	1	12 V active-low Hall, timer capture
Cam trigger input	1	12 V active-low Hall, timer capture
Deadman inputs	2	Dedicated, independent 5 V vehicle-logic engine-permit inputs
Thermistor inputs	4	Air, oil, water, and one spare temperature input
General analogue inputs	9	Protected 0-5 V sensor channels
ADC rail-monitor channels	3	VBAT_PROT, +5V_SENS, and +12V_SENS
Ignition output	1	Dedicated coil low-side driver
Injector output	1	Dedicated injector low-side driver
Generic digital inputs	Provisionally 6	Protected 5 V / 12 V compatible inputs
Generic logic outputs	Provisionally 4	Protected 5 V logic outputs
Generic sink outputs	Provisionally 4	Protected low-side outputs
Analogue outputs	Reserve 2 MCU/output paths	Future 0-5 V output capability; not a V1 requirement

The provisional generic digital I/O counts are planning values, not a frozen connector or pin budget. CAN and its physical layer are intentionally outside the scope of this document.

Power-Domain Rules

• +5V_MAIN is the primary internal regulated 5 V rail. It supplies internal 5 V circuitry and is the upstream rail for +5V_AUX and +5V_SENS; it is not connected directly to external harness loads.
• +5V_SENS is exclusively for sensor excitation and thermistor pull-ups. It is never used to power generic peripherals or output loads.
• +5V_AUX powers external 5 V logic-level output circuitry. It is separately protected so an external fault cannot disturb sensor excitation.
• +12V_SENS is the regulated buck-boost Hall/12 V sensor supply. It is kept separate from arbitrary digital output loads.
• VBAT_PROT supplies the ignition, injector, and protected low-side output branches. It is the 12 V-class source for general load-driving interfaces.
• High-current ignition, injector, and load-driver returns remain separate from the sensor and MCU returns until their deliberate join at the power entry region.

Engine-Position Inputs

Crank and cam are dedicated timer-capture inputs, not generic digital inputs. The V1 timing pattern remains two crank pulses per revolution and one cam pulse per 720-degree cycle. Their interface, harness/shield termination, protection, conditioning, and hardware/firmware glitch-rejection requirements are defined in ENGINE_POSITION_INPUTS.md.

Analogue Inputs

ADC allocation

The STM32H747 provides three ADC peripherals. ADC1 and ADC2 share most of the external analogue-pin pool, so they increase concurrent conversion capacity rather than doubling the number of physical sensor pins. The proposed V1 allocation occupies 16 conditioned ADC channels:

Conditioned ADC input class	Channels
Thermistors	4
General 0–5 V inputs	9
VBAT_PROT sense	1
+5V_SENS sense	1
+12V_SENS sense	1
Total	16

This leaves meaningful MCU ADC and pin margin, but the final STM32 package and pin assignment must reserve all analogue pins alongside timer, CAN, debug, I2C, and optional DAC requirements. In particular, PA4 and PA5 should remain available if the two internal DAC outputs are to be retained for future analogue outputs.

Thermistor channels

Each thermistor channel is excited from +5V_SENS using a precision pull-up. The input is attenuated and filtered before the ADC; this remains required because an open thermistor drives the node towards 5 V. Firmware calculates the thermistor resistance from the ratio of its ADC result to the +5V_SENS ADC result, then applies the calibration map for the selected sensor.

The pull-up value is selected from the actual NTC curve and required temperature range, balancing resolution against self-heating. The attenuation network should be high impedance enough that it does not materially load the thermistor divider; the ADC sample time and local input capacitor must then be chosen to achieve settling. The initial Bosch 2.5 kOhm NTC population is a 3.01 kOhm precision pull-up; 10.0 kOhm and 30.1 kOhm alternatives are reserved only for confirmed sensor curves. See ANALOG_INPUTS.md for the detailed architecture.

General 0-5 V channels

General analogue inputs support conventional 0.5-4.5 V and 0-5 V automotive sensors. Each includes connector protection, attenuation, and an ADC-local filter capacitor. A nominal attenuation ratio near 0.55 maps a 5.25 V sensor signal to about 2.9 V at an ADC referenced by +3V3_ANA.

General analogue inputs are passive. Their dividers, filter capacitors, and ADC acquisition time must be selected together to meet source-impedance and settling requirements. A genuinely high-impedance or special-purpose sensor requires a dedicated front end rather than altering the generic channel.

+5V_SENS is measured through an equivalent matched divider/filter path and sampled near each ratiometric sensor channel. Firmware uses the ratio of the sensor and supply readings to cancel sensor-supply and ADC-reference variation.

Battery and Rail Measurements

VBAT_PROT is measured by a protected, scaled direct ADC channel. This is the deterministic engine-control measurement used for battery-voltage dwell and injector compensation. The M7 should receive a DMA-updated, filtered value and snapshot it immediately before scheduling a dwell event.

Voltage/current monitor ICs may monitor the regulated rails for telemetry and diagnostics. They are not the sole engine-control voltage source. In particular, no whole-ECU current shunt is placed in series with VBAT_PROT; coil and injector pulse currents would waste power and make that measurement less useful. Upstream protection is provided by the input fuse/e-fuse and local protection is provided by the ignition and injector driver stages.

Generic Digital Inputs

Generic digital inputs accept externally driven 5 V through VBAT_PROT active-high signals, with software-configurable reported polarity. They are not intended for crank or cam capture. The detailed interface, including fail-safe ECU-off behavior, external hysteresis, optional wetting/pull-down footprints, and harness protection, is defined in DIGITAL_INPUTS.md.

The generic input front end uses fail-safe, 40 V-capable open-drain comparators powered by +3V3_MAIN, with thresholds derived from +5V_MAIN. The input is protected at the connector and cannot back-power the ECU when an external source drives it while the ECU is unpowered. The final transient protection, threshold, hysteresis, filter, and bias values remain pending the actual harness and input-function requirements.

Deadman Engine-Permit Interlock

The deadman uses two dedicated 5 V vehicle-logic inputs, not generic digital inputs. The steering-wheel switch provides two electrically independent, normally-open contacts. Each contact has its own connector pin, protection, filtering, default-low bias, and conditioned logic path. This makes an open circuit or a short to the 5 V source on one signal path non-permissive.

The resulting 5 V DEADMAN_OK signal is high only when channel A reports held and the independently conditioned, inverted channel B reports not released. It has two independent destinations:

• DEADMAN_A_STATUS and DEADMAN_B_STATUS enter MCU digital inputs so firmware can observe each contact, detect disagreement, disable scheduling, and report the state.
• DEADMAN_OK is combined in hardware with the MCU's MCU_RUN_PERMIT output to produce ENGINE_PERMIT.

ENGINE_PERMIT controls the enable inputs of the injector and ignition drivers where those inputs are provided. If a selected driver has no suitable enable input, ENGINE_PERMIT is ANDed with that driver's MCU command signal using logic that defaults to the disabled state on power-up or loss of power.

This hardware path ensures that releasing the deadman, an open circuit, or a single signal-path short to the 5 V source stops injector and ignition commands even if firmware or a timer output fails to respond. It does not claim to cover a common-mode fault that energises both paths. Firmware must clear/disable pending injection and dwell schedules whenever DEADMAN_OK becomes invalid or the two MCU status inputs disagree. A firmware test mode may assert MCU_RUN_PERMIT, but it does not override the physical deadman inputs; bench operation requires a deliberate external test arrangement that presents the valid two-channel held state. The detailed signal and fault model is defined in DEAD_MAN.md.

Outputs

Ignition and injector

The ignition coil is supplied from VBAT_PROT and switched with a dedicated automotive ignition driver or smart ignition IGBT. It requires controlled primary flyback clamping, over-current and thermal protection, and fault reporting. Firmware applies battery-voltage dwell compensation using the direct VBAT_PROT ADC measurement; driver current limiting remains the safety backstop.

The injector is supplied from VBAT_PROT and switched by a dedicated automotive smart low-side driver. It requires inductive-load capability, controlled turn-off clamping, current/thermal protection, and MCU-readable open-load and short-circuit diagnostics. This assumes a conventional high-impedance/saturated injector; a low-impedance injector requires a peak-and-hold architecture.

Generic digital outputs

All non-engine digital output connector functions are labelled generically and assigned their vehicle role in firmware. For example, the starter-enable function is mapped to a compatible generic output rather than having a dedicated connector-only electrical architecture.

Two hardware classes remain necessary. Their selected architecture, default state, diagnostic intent, connector protection, and remaining validation are defined in DIGITAL_OUTPUTS.md.

• Generic logic outputs use +5V_AUX-supplied TPS4H000-Q1 protected high-side channels with a local output pull-down. They command external electronic-control inputs and are limited to 100 mA per channel.
• Generic sink outputs use VBAT_PROT-supplied TLE9104SH protected low-side channels. They command relays, solenoids, and external modules that provide a pull-up.

Firmware configuration selects the output's vehicle role and active polarity, but cannot make one electrical driver class behave as the other. A starter enable can therefore use either a generic logic output or a generic sink output only when the selected external starter switch accepts that interface.

Analogue-output provision

Analogue output is not a V1 functional requirement. Reserve two MCU pins and board footprints for future 0-5 V outputs. The intended future path is:

A true calibrated 0-5 V output may require an external 5 V-referenced DAC or a suitably characterised buffer stage. A general 0-12 V analogue output is not included unless a future peripheral explicitly requires it.

Layout and Validation Priorities

• Keep trigger and ADC front ends physically separated from coil, injector, switching-regulator, and high-current output nodes.
• Place protection at the connector, filtering/conditioning near the MCU side, and avoid dumping input-fault energy into +3V3_ANA.
• Validate Hall glitch rejection with ignition active, including worst-case dwell and spark events.
• Validate ADC noise, ratiometric accuracy, thermistor self-heating, and ADC settling before freezing resistor networks or deciding whether the optional analogue LDO is necessary.

Open Items Before Schematic Freeze

1. Select Hall and thermistor part numbers, cable lengths, connectors, and resulting pull-up/filter values.
2. Confirm ignition-coil and injector electrical data and select their driver devices.
3. Freeze the generic digital I/O count, per-channel current ratings, and connector allocation.
4. Select 5 V-tolerant, automotive-suitable comparators and input-protection components for generic digital inputs.
5. Select the STM32H747 package and complete a pin assignment that preserves all timer, ADC, optional DAC, debug, and communications resources.
6. Define CAN and other communications interfaces separately.