Moved readme to root

README.md

@@ -1,2 +1,43 @@
-# Bench Data
+# Bench-Data
-This repository contains both the arduino firmware and python connector to feed RPM and Lambda to a dynalab-core software
+
+> [!WARNING]
+> This software was developped for linux, Windows compatibility is not guaranted
+
+This repository contains both the arduino firmware and python connector to feed RPM and Lambda to a dynalab-core software
+## Requirements
+To use the software you will need to install `uv` to manage the python project [docs.astral.sh](https://docs.astral.sh/uv/getting-started/installation/)
+## Setup
+First, clone the repository: 
+```bash
+git clone https://git.h3cx.dev/Exergie/Bench-Data-Processing.git
+```
+After that, you will need to go to the connector repository and sync the project:
+```bash
+cd Bench-data/bench-data-connector
+uv sync
+``` 
+Then to run the program you will just have to run the following command into your terminal:
+```bash
+uv run bench-data-connector
+``` 
+## Usage
+To use the program you will have to plug in the arduino into a port of your pc. Then when the program is executed you will have to select the port where the arduino is pluged in.
+```
+27: /dev/ttyS5 n/a
+28: /dev/ttyS3 n/a
+29: /dev/ttyS2 n/a
+30: /dev/ttyS1 n/a
+31: /dev/ttyS0 n/a
+32: /dev/ttyUSB0 USB Serial
+Choose a port to connect: 32
+```
+Once the port is selected the arduino is going to operate a sync with the pc during 30 seconds, so no data will appear in the first 30 seconds.
+```
+Waiting 5 seconds before synchronization...
+```
+Once the sync is done the data should start to appear:
+```
+sync ok
+Offset:2626280123208.57
+Scale:1.006884777346364
+```

bench-data-connector/README.md

@@ -1,43 +0,0 @@
-# Bench-Data
-
-> [!WARNING]
-> This software was developped for linux, Windows compatibility is not guaranted
-
-This repository contains both the arduino firmware and python connector to feed RPM and Lambda to a dynalab-core software
-## Requirements
-To use the software you will need to install `uv` to manage the python project [docs.astral.sh](https://docs.astral.sh/uv/getting-started/installation/)
-## Setup
-First, clone the repository: 
-```bash
-git clone https://git.h3cx.dev/Exergie/Bench-Data-Processing.git
-```
-After that, you will need to go to the connector repository and sync the project:
-```bash
-cd Bench-data/bench-data-connector
-uv sync
-``` 
-Then to run the program you will just have to run the following command into your terminal:
-```bash
-uv run bench-data-connector
-``` 
-## Usage
-To use the program you will have to plug in the arduino into a port of your pc. Then when the program is executed you will have to select the port where the arduino is pluged in.
-```
-27: /dev/ttyS5 n/a
-28: /dev/ttyS3 n/a
-29: /dev/ttyS2 n/a
-30: /dev/ttyS1 n/a
-31: /dev/ttyS0 n/a
-32: /dev/ttyUSB0 USB Serial
-Choose a port to connect: 32
-```
-Once the port is selected the arduino is going to operate a sync with the pc during 30 seconds, so no data will appear in the first 30 seconds.
-```
-Waiting 5 seconds before synchronization...
-```
-Once the sync is done the data should start to appear:
-```
-sync ok
-Offset:2626280123208.57
-Scale:1.006884777346364
-```